当前位置: 首页 > 资讯中心 > 公司动态

举升机的操作应该注意什么?

时间:2021-06-30 19:51:50  浏览次数:

1、举升机在使用前应清除附近妨碍作业的器具及杂物,并检查操作手柄是否正常.

1. Before using the lift, remove the nearby appliances and sundries, and check whether the operating handle is normal

2、举升机操作机构是否灵敏有效,液压系统不允许有爬行现象.

2. Lift operating mechanism is sensitive and effective, hydraulic system is not allowed to crawl

3、待举升车辆驶入后,应将举升机支撑块调整移动对正该车型规定的举升点.

3. After the lifting vehicle is driven in, adjust and move the lifting support block to the specified lifting point of the vehicle

4、举升机在支车时,四个支角应在同一平面上,调整支角胶垫高度使其接触车辆底盘支撑部位.并且车辆不可支得过高,支起后四个托架要锁紧.举升要稳,降落要慢.

4. When the lift is supporting, the four supporting angles should be on the same plane. Adjust the height of the rubber pad of the supporting angle to make it contact the supporting part of the vehicle chassis. The vehicle should not be supported too high. After supporting, the four brackets should be locked. The lifting should be stable and the landing should be slow

5、举升时人员应离开车辆,举升到需要高度时,必须插入保险锁销,并确保安全可靠才可开始到车底作业.

5. When lifting, the personnel should leave the vehicle. When lifting to the required height, the safety lock pin must be inserted to ensure safety and reliability before starting to work under the vehicle

6、除底保及小修项目外,其他繁琐笨重作业,不得在举升机上操作修理.

6. Except for basic maintenance and minor repair items, other cumbersome and heavy operations are not allowed to operate and repair on the lift

7、举升机不得频繁起落.

7. The lift should not take off and land frequently

8、有人作业时严禁升降举升机.

8. It is forbidden to lift the lift when someone is working

9、发现操作机构不灵,电机不同步,托架不平或液压部分漏油等故障,应及时报修,不得带病操作.

9. If the operating mechanism is not working properly, the motor is not synchronized, the bracket is uneven or the hydraulic part leaks oil, it is necessary to report for repair in time

10、作业完毕应清除杂物,打扫举升机周围以保持场地整洁.

10. After the operation, the sundries should be removed and the area around the lift should be cleaned to keep the site clean

11、定期排除举升机油缸积水,并检查油量,油量不足应及时加注相同牌号的压力油.同时应检查润滑、举升机传动齿轮及缝条.

11. Regularly remove the water in the oil cylinder of the lift, and check the oil quantity. If the oil quantity is insufficient, add the pressure oil of the same brand in time. At the same time, check the lubrication, transmission gear and seam strip of the lift

举升机的操作应该注意什么?

1、举升机在使用前应清除附近妨碍作业的器具及杂物,并检查操作手柄是否正常.

1. Before using the lift, remove the nearby appliances and sundries, and check whether the operating handle is normal

2、举升机操作机构是否灵敏有效,液压系统不允许有爬行现象.

2. Lift operating mechanism is sensitive and effective, hydraulic system is not allowed to crawl

3、待举升车辆驶入后,应将举升机支撑块调整移动对正该车型规定的举升点.

3. After the lifting vehicle is driven in, adjust and move the lifting support block to the specified lifting point of the vehicle

4、举升机在支车时,四个支角应在同一平面上,调整支角胶垫高度使其接触车辆底盘支撑部位.并且车辆不可支得过高,支起后四个托架要锁紧.举升要稳,降落要慢.

4. When the lift is supporting, the four supporting angles should be on the same plane. Adjust the height of the rubber pad of the supporting angle to make it contact the supporting part of the vehicle chassis. The vehicle should not be supported too high. After supporting, the four brackets should be locked. The lifting should be stable and the landing should be slow

5、举升时人员应离开车辆,举升到需要高度时,必须插入保险锁销,并确保安全可靠才可开始到车底作业.

5. When lifting, the personnel should leave the vehicle. When lifting to the required height, the safety lock pin must be inserted to ensure safety and reliability before starting to work under the vehicle

6、除底保及小修项目外,其他繁琐笨重作业,不得在举升机上操作修理.

6. Except for basic maintenance and minor repair items, other cumbersome and heavy operations are not allowed to operate and repair on the lift

7、举升机不得频繁起落.

7. The lift should not take off and land frequently

8、有人作业时严禁升降举升机.

8. It is forbidden to lift the lift when someone is working

9、发现操作机构不灵,电机不同步,托架不平或液压部分漏油等故障,应及时报修,不得带病操作.

9. If the operating mechanism is not working properly, the motor is not synchronized, the bracket is uneven or the hydraulic part leaks oil, it is necessary to report for repair in time

10、作业完毕应清除杂物,打扫举升机周围以保持场地整洁.

10. After the operation, the sundries should be removed and the area around the lift should be cleaned to keep the site clean

11、定期排除举升机油缸积水,并检查油量,油量不足应及时加注相同牌号的压力油.同时应检查润滑、举升机传动齿轮及缝条.

11. Regularly remove the water in the oil cylinder of the lift, and check the oil quantity. If the oil quantity is insufficient, add the pressure oil of the same brand in time. At the same time, check the lubrication, transmission gear and seam strip of the lift
下一篇:返回列表